• Why device can not find USB flash drive
  • After plug device to pc via USB, prompt message “can not recognize the USB device”
  • OA1000 SQLITE_MISUSE Error
  • VF30 keypad flash
  • Device time issue
  • How to set the device back to factory default
  • Forget password of Facepas/Facepass Pro
  • Why the user register in the device can not open the door
  • Why the device can not read the fingerprint
  • Interim signal module introduction SC011/DAC844
  • T60 GPRS Operation Guide
  • E-Lock connection
  • How A300 connect TO printer?
  • T60 and T5 Pro Wiegand connect and enroll user
  • Anti-Passback function.

    Q:
    Anti-Passback function.

    A:

    T5S and T60 Anti-Passback function

     

    Background: Do you know what’s Anti-Passback function?

     

    Anti-Passback Feature in Access Control Systems

     

    The anti-passback feature is designed to prevent misuse of the access control system.

    The anti-passback feature establishes a specific sequence in which only access cards can

    be used in order for the system to grant access.


    The anti-pass back feature is most commonly used at parking gates, where there is both

    an “in” reader at the entry gate and an “out” reader at the exit gate. 


    There should be a corresponding use at the “out” reader before the card can be used at the “in” reader

    again. For the typical user of the parking lot, it works on well, because the user would normally

    swipe their card at the “in” reader to get into the lot in the morning, and swipe it at the “out” reader

    to get out of the lot in the evening.  However, if a user swipes his card at the “in” reader to get in, and then passes his card back

    to a friend, the card would not work the second time when it was swiped by the friend. The attempt to use

    the card a second time would create an “in – in” sequence that is a violation of the anti-passback rules,

    and this is why access would be denied.

     

    Anti-passback can also be used at employee entrance doors. This requires that a card reader be installed

    on both the inside and the outside of the door. Employees are required to both "card-in" when they enter the

    building and "card-out" when they leave the building. The anti-passback feature is also commonly used with turnstiles.

     

    There is an expanded version of the anti-passback feature called “regional anti-passback”. This establishes

    an additional set of rules for card readers inside of the building itself. Basically, this rule says that unless a

    card is first used at an “in” reader at the building exterior, it cannot be used at any reader within the interior

    of the building. The theory is that, if a person did not enter through an approved building entrance, he or she

    should not be permitted to use any of the readers within the building.

     

    Depending on the access control system manufacturer, there may be additional anti-passback features in

    the system. Some of these features could include "timed anti-passback", which requires that a designated

    amount time pass before an access card can be used at the same reader again, and "nested anti-passback"

    which requires that readers be used in only designated sequence to enter or leave a highly-secured area.

     

    Denying access when a user attempts to use a card out of sequence is sometimes called "hard" anti-passback.

    Hard anti-passback means that when a violation of the anti-passback rules occurs, the user will be denied access.

    Some access control systems also offer a feature known as "soft" anti-passback. When a system is using this option,

    users who violate anti-passback rules are permitted access, but the incident is reported to the person managing the

    access control system so that corrective action can be taken - most often notifying the offending employee that the access

    card should be used in the proper sequence in the future.

     

    The anti-passback feature can also be integrated with the corporate computer system, preventing users from logging on to

    the network at their desktop computer unless they have properly entered the building using their access card. This feature

    can also temporarily disable the users remote log-on privileges while the user is in the building - the theory being that if the

    user is at work, there is no reason for someone from off-site to be logging on to the network using his or her user name

    and password. When the user leaves the building at the end of the day, his or her remote log-on privileges are turned back on.

     

    From Google

     

    1. T60 firmware V2.07 and above, T5s firmware V1.36 and above

     

           2.  Wiring diagram.

     

    T60 RS485A connect to T5s RS485A

    T60 RS485B connect to T5s RS485B

     

          3.  Enable the anti-passback function on the T60.

     

     

    Enabled  Yes, means enable the anti-passback function.

     

    Native   In , when you select In, means that the device be installed at outside, the device is entry door.

            Out, when you select Out, means that the device be installed at inside, the device is exit door.

     

    PS: In general, T60 is installed at outside , as a entry door, normally will select in status.

     

    Empty User: when you identification pass on the device, means that there is one user have already entry

    into the door, so in that case , you will see have one number on the top right corner of the LCD.

    Empty User function, if one guy entry door, then tail with other guys exit door, in next entry into the door,

    he can’t entry into the door, so we have to empty user in order to the guy can entry into the door.

     

    If you identification pass on the T5s, then the number will minus one.

    Notice: Please don’t forget to punch card/ identification fingerprint on the device.

  1.  1  2 
  2. 21 Records 1/2 Page
Newsletter
×